Model Steam Engine Relief Valves

Model Steam Safety Valves –┬áRelief Valves

Model steam engine safety valves, or relief valves as they are otherwise known, are needed on live steam boilers to provide a safe working pressure within the boiler.

As the pressure builds inside the boiler through the added heat input, the valve (ball) – kept in place usually by spring pressure, lifts from its seating and allows surplus pressure to escape to the atmosphere in a safe manner, re-seating once again as the excess pressure is reduced to where it should be.

Safety valves for steam engine pressure control

 

These safety valves for live steam models are generally stainless steel balls sitting against a softer metal, usually brass, using either gravity or spring pressure to keep the seal intact.

The internal spring needs to hold the ball in place until the pressure in the boiler rises and pushes against the spring pressure and lifts the ball.

For the gravity type, there tends to be a small weight sitting on the end of an arm to force a rod down on the top of the ball, with the boiler trying to lift the ball from below.

Obviously this type needs to be sat in an upright position to work properly and the pressure can be adjusted by changing the weight or moving the distance of the weight, either inwards for less or outwards for more, from the pushrod sitting on top of the ball.

Testing is simply lifting the end of the rod slightly to see steam being vented before making sure the pressure is replaced. Best do this with a rod so you do not get scalded in the process.

In both cases, a stainless steel rod with a flange on it can replace the ball much like a motor car tire valve.

Spring Type Safety Valves

 

In the case of adjusting the spring type of relief valve, usually there is a screw adjustment at the top of the safety valve allowing the spring to be either compressed to exert more pressure on the ball and hence inside the boiler, or released to allow the boiler pressure to be maintained at a lower level.

If you find you have a low-pressure boiler and the relief valve does not blow off at the wanted pressure it is possible to install a shorter spring to achieve the desired pressure or alternatively by boring the steam passage out a little and using a bigger ball, that way allowing the ball to be lifted more readily by the lesser steam pressure.

Do not be tempted to install any old spring of the right dimension as these can rust or become softened and relaxed owing to the steam and changeable heating of the boiler, that way making the relief valve blow off at very little pressure or possibly not allowing any pressure to be held within the boiler owing to there being no seal between the ball and its seating.

To make a steam relief valve steam tight it is simply a matter of removing the cap or screw adjustment, take out the spring relief valve and tap the stainless ball with a softer metal to remake the seat. After re-assembly, all that is needed is to reset the pressure rating for the safety valve by adjusting the pressure on the spring.

However, do not go in for one that has a much higher pressure than needed, as the springs inside are much tougher and adjustment for lower pressures will not be achievable as you will need weaker springs installed to achieve anything like what you want.

In the same way, a weaker spring can be replaced to produce a greater pressure relief where necessary.

A quick tap on the top of the rod causes the spring to rebound and allow a little steam to escape.

Using Pressure Relief Valves

 

Moving onto actual usage, it is wisest to test the working ability of your safety valve at each steam up, making sure it does not allow the pressure to rise more than 10% above what it is meant to do, and also that it reseals to allow the pressure to build up to its correct level.

Simply tapping the top of the valve stem when under pressure should allow steam to blast out of the top of the valve. This is to check that the valve is not stuck and could possibly do some damage to yourself or the surroundings.

Other types of valves where the valve stem is not exposed means just keeping an eye on the pressure and being prepared to shut off the heat if the pressure gets too high.

This 10% margin is what is demanded in the present-day steam regulations, as with the self-build PYRTE Traction Engine, with a working pressure of 50 lbs per square inch, a pressure of 55 lbs is allowed, but it must go no higher than that.

What normally happens nowadays is that two safety valves are installed so that, as in the case of PYRTE, one lifts at 50lbs/square inch and the second at 55 lbs (or slightly less – the 10%) to provide a safety margin should the first one fail to lift.

After all, they are there for your safety and anyone else in close vicinity.

Leave a Reply

Your email address will not be published. Required fields are marked *